Filled in all around . No more flowers other than that one.

5/15 5/27

6/8 6/18

6/29

7/11

GAZEBO ADORNMENT - HOO ARE YOU? LINK

Its time for edition #5 of Hoo Are You Tuesday!


If you want to play along be sure to link up with Leslie at Night Owl Crafting!

1. What is your favorite restaurant?

My favorite restaurant is a local one called McQuire's. We like to eat there because the food is good, it's close , and we see people we know to chat with.

2. What kind of music do you like?

I like pretty much all kinds of music, except heavy metal and rap. I prefer lyrics that are not derogatory to humans in general. I do listen to Country most; however, in the car.

3. What do you watch on TV?

I watch a variety of shows on TV, but I guess my favorites are the CSI's and shows of that nature. We don't have cable or satelite, but there are enough channels that we get over the air, that I still have to record shows to the DVR! I particularly record shows on the CREATE channel. I love their how to shows.

4. Do you enjoy reading and if so what kind of 

books do you read?

I do like to read, but seldom make time for it. The kinds of books I tend to gravitate toward are either romantic fiction or who done it. I prefer female authors, because, frankly the sex is better and the plots more everyday life. Some of my favorite authors are Sue Grafton, Sandra Brown, and Susan Wittag Albert.

5. What is your favorite color?

My favorite color appears to be purple. I say this because when I was looking at the flowers I planted out by the deck, most of them were shades of purple.

Before

and...

After

This is how our gazebo has looked for years. The table was never easy to clean with the deck stain we originally put on it, so I put a tarp over it, which was ok.... for awhile.  

I always felt it needed dressing up, so this is what I did: 

I painted the table with brown exterior latex paint and then painted on the flower and stenciled edges with acrylic paint. I sealed the whole top with concrete sealer. It has come through one winter just fine, so I think it will be alright.

I made some curtain rods to fit out of 3/8” steel rod and I painted telephone insulators [the kind that attaches to the house] to use as brackets. 

The “curtains” are shower curtains, which I got on clearance for $5.00 a set. I used some black hair bands [‘cause Walmart didn’t have black elastic] which I sewed into the tiebacks. I painted fence insulators and attached them to the outside of the posts to hook the tiebacks to.

The final touch when I get around to it is to make some matching cushions for the benches.

The potato tower looks good. The front has filled in and I even got my first flower.

5/15 5/27
6/8 6/18
6/29

DECK STOOLS

I needed some stools for the table in our gazebo.

I was thinking something on the order of these at mypatiogardenfurniture.com, but I'm too cheap to buy them and I couldn't find any easy plan to make them.

So I decided to steal borrow Ana's ladder table plans.
A little tweaking to make it sturdier to sit on and I think we've got a winner.

Here's hers:

And here's mine:

  

This is how I built them.

Tools I used:                                     Materials:

 Table Saw                                          (2) 6 ft Treated Deck Boards (5/4" X 6")

 Miter Saw                                           2" Deck Screws

 Tape Measure

 Carpenter's Square

 Drill and bit including countersink bit

I pretty much followed Ana's plans except that I made them a little shorter and I used 5/4" treated deck boards instead of  1x3's and 1x2's. This did require ripping some of the boards on the table saw, but I wanted something that would be for outdoors.

This is the cut list of the pieces I used. 

Cut all the pieces to length with the miter saw, then rip all but [2] 14" boards and [2] 10 1/2" boards, which will be used for the seat and bottom shelf, to 2 1/2". [Leave the highlighted pieces full width.]

For all pieces: Drill holes for the screws and use a countersink bit to make depressions in the boards so the screws will countersink. Be sure the rounded side of the boards are all facing to the front for the seat, shelf and legs. For the seat and shelf supports, the rounded edge will be facing down.

Make the seat support by making a box frame with
[2]10 1/2" X 2 1/2" boards and  [2] 5" X 2 1/2" boards.  Square up the piece with the carpenter's square and  use clamps to keep it in place. Make sure the flat sides of the boards are flush [even]. Screw it together using 2" coated deck screws. When you have all the screws in place, remove the clamps and set the middle 5" X 2 1/2" board in and repeat the clamping and screwing process.

Assemble the seat by placing [2] 14" X 5 1/2" boards on top of the frame you just made and clamp to keep in place, and centered. At all steps be sure to measure, measure, measure, and make minor adjustments as necessary. Drill and screw down as before.



Build the shelf support similar to the seat support, except it will be a "ladder type" form instead of a box frame, using [2] 10 1/2" X 2 1/2"  boards and [2] 9" X 2 1/2" boards. Attach the 9" boards 2" from the ends of the 10 1/2" boards, as shown in the image below.



Assemble the shelf in the same manner as the seat, using [2] 10 1/2" X 5 1/2" boards and [1] 10 1/2" X 2 1/2" boards. The cut board will be the rear of the shelf, cut side to the back. The ends of the top boards will be flush with the ends of the 10 1/2" boards. Make sure you have a slightly longer overlap in the front than the back. Again, be sure to measure carefully and clamp in place. Drill and screw together.

This is the finished shelf. Note the cut side at the back.

Cut the legs on the miter saw. Clamp the [2] front legs together and cut first one end at 20°, through both boards. Measure for the length you want and cut the other side parallel to the first side, at 20°. Repeat this process for the back legs, except they are cut at 5°.



Assemble the stool beginning with a front leg and back leg on one side. Make sure the rounded edges are facing to the front of the stool. Line up the back leg at the top to the edge of the seat support frame in the back and line up the front leg at the top to the edge of the seat support frame in the front. Here is a nice image from Ana that shows the position.

www.knock-offwood.com

Clamp in place and drill  and screw together. Repeat for the other [2] legs. Use the carpenter's square to make sure the legs are level with each other, front to back, side to side, and diagonally.



 I did have to nip off the front corners at 45°, because it was just too sharp to slide onto next to the table. When I put a finish on these after the wood has dried, I'll sand down the edges a little so that there are no sharp edges.

And here are the finished stools; sans paint and stain.

GUEST BLOGGING

Hi there friends!  Rayan - the Frugal Designer here to tell you that your Blogger has been kidnapped...by me!  Not to worry, it's only temporary, I promise to return them shortly and in one piece!  I hope you will come visit them over at my site, I know they would love to see you all and I would be honored to have you as well!  See you soon..Xx Rayan!

Tru here:
"I will be guest blogging on  The Frugal Designer tonight at 9PM CST, my time, (7PM PST)                                                          

Please pop on over and see me. While you're there, check out her site The Frugal Designer
It's one of those blogs that has a lot to offer; not just her own projects, but she also showcases other bloggers' projects as well. She is certainly helping me to get recognized by other bloggers."